PLUMBING 101: TIPS FOR BATHTUB INSTALLATION

Plumbing 101: Tips for Bathtub Installation

Plumbing 101: Tips for Bathtub Installation

Blog Article

Request Service

The author is making several good annotation regarding Tools You Need to Install a New Bathtub overall in this content down the page.


How to Install a Bathtub
Setting up a tub isn't exactly brain surgery, yet it does need strong plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old tub with a new one is also a reasonably tough project. If the old bathtub is readily obtainable, the job can move speedily; if you need to open up a wall surface to eliminate the old tub and place the new tub, the job is much harder. In either instance, the job is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the new one. Ensure you have actually qualified yourself for the job and also fit trying it. Instead of working with a professional to take control of a halfway-completed project, it is much better to consider utilizing one before you start. Opportunities are you might need a professional plumber to make tube links.
This article will assist you install a new tub in your bathroom if you have already bought a brand-new tub and also don't require to change the setup of your previous supply of water pipelines.
Your tools and also material list should make up the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you require to change old taps with new ones as a part of your installment, then the first thing you should do is disconnect the supply of water. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite bothersome because of the restricted access that is frequently the case.
    Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will certainly originate from the pipes. As soon as the supply pipes have actually been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
    Prior to going on to fit the brand-new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.

    Fitting New Taps


    If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end gives a connection to the existent supply pipelines.
    If you require to fit a monobloc, after that you will certainly need lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
    Next, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in location between the tap and the sink. Protect the tap in position with the maker offered backnut. Once the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap ports. The former type should be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.

    Setting up the Bathtub


    Using both wood boards under its feet, position the bathtub in the required setting. The wood boards are handy in uniformly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four tiny points.
    The next goal is to make certain that the bathtub is leveled all round. This can be attained by examining the level and adjusting the feet on the bathtub until the spirit level reviews degree.
    To mount taps, fit all-time low of the outermost flexible tap connector to the proper supply pipe by making a compression sign up with; then do the same for the other tap.
    Turn on the water and also check all joints as well as new pipework for leaks and tighten them if necessary. Fill the bath tub as well as additionally check the overflow electrical outlet and also the typical electrical outlet for leaks.
    Ultimately, deal with the bathroom paneling as described in the maker's instruction manual. Tiling as well as sealing around the bath tub should wait till the tub has been used a minimum of once as this will resolve it right into its final setting.

    Getting ready for the Installment


    Firstly, the sustaining framework provided with the bathroom should be fitted (if needed) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to make sure that if the faucet includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the faucets unit to prevent stress on the bathtub.
    Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use every one of the provided washers.
    Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its final placement.

    Tiling Around the Bath tub


    In the location where the bathroom satisfies the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture a stiff seal, causing the water to penetrate the wall surface in between the bath and the tiling, resulting in problems with wetness as well as possible leaks to the ceiling below.
    You can select from a variety of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes and cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill the bathtub with water before sealing, to allow for the movement experienced when the bathtub is in usage. The sealant can crack fairly early if you do not take into account this activity prior to securing.
    Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily readily available on the marketplace. It is suggested to fit the ceramic tiles using water-resistant or water resistant adhesive as well as grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Installing A Bathtub

    Do you really like reading up on Tools You Need to Install a New Bathtub ? Give feedback down below. We'd be pleased to see your opinions about this blog. Hoping that you come back again soon. For those who appreciated our article please do not forget to pass it around. Bless you for your time. Kindly check our website back soon.


    24-hour service? Dial here.

    Report this page